The Journal of Industry and Technology

Industrial Analytical Instrumentation

Euro Technology

Serving industry for over 36 years
Three leading magazines for key executives,  engineers, universities,
manufacturers, laboratory technicians, scientists, and research establishments

Total engineering and manufacturing

Resistor liquid cooling boosts 3.3kV medium voltage loads

In motor driven applications like cranes, lifts, hoists and conveyors, air cooled resistors are common, but in medium voltage, high power applications liquid cooling wins out. A medium voltage drive running off a 3.3kV supply to turn a 500kW motor will put a severe heating load on the application's power transistors - hence the need for water cooling, as David Atkins, projects director at Cressall Resistors explains.

The new EV2 advanced water cooled modular resistor range for low and medium voltage applications is especially designed to function in severe environments, like the ones marine systems have to function in. This patented design encapsulates and completely separates the resistor elements from the coolant.

Water cooling
If 1MW or more of heat needs to be dissipated, direct water cooling makes more sense. A typical 1MW fresh water-cooled brake resistor for marine use is basically a 10 foot tube with large heating elements similar to those found in common household kettles. The braking electricity that is being regenerated powers these elements. Most ships have a chilled water system, which circulates cool water throughout the vessel, used for both air conditioning and equipment cooling.

There is also a sea water variant with construction and ratings similar to the fresh water designs, but with titanium-sheathed elements in higher-grade stainless steel vessels, suitable for continuous duty in hot sea water. The problem is that heating elements cannot be used here at an operating voltage of much above 1.5kV, whereas medium voltage drives will typically use a 3.3kV supply.

Cressall's EV2 resistor is not limited by this restriction. This is a 25kW unit available as a single unit or as a block with a common cable box attached to 250kW braking power input using a common water supply. Cold water comes in one end and hot water comes out the other. The EV2 has the advantage of higher operating voltage, lower weight and compactness, and is therefore ideal for marine applications.

Over the last ten years shaft-driven shipboard mechanical power transmission has been increasingly replaced by electrical power. For example, both the Royal Navy Type 45 destroyer and the Queen Elizabeth carrier are electrically driven. The prime mover is used solely for generating electricity, which is then distributed to various motors, including those driving the propeller shaft(s), and other consumer loads.

All-electric ship design
The logic behind all-electric ship design that is two-fold. Firstly, ship layout - a large motor does not need to be in the middle of the ship, which is better used as prime passenger and cargo space. Secondly - energy efficiency. Traditional ships could have up to four diesel engines located mid-ship running at low power under normal operating circumstances. This often made them inefficient. By using smaller diesel engines together with a couple of gas turbines, the right number of prime movers can be fired up to suit power demand, whether it is a fully-laden oil tanker afloat at sea or stationary at port.

In drilling or cable-laying vessels, where anything up to a mile of cable has to be paid out over the side during passage, the weight of the cable is so massive, that the drive motor has to reverse its function from motor to generator, in order to brake the cable reel. Air cooled resistors have heating elements enclosed within a fan cooled cabinet. This makes them suitable for deck mounting, often on anti-vibration mounts.

An important benefit from using an electric drive is that reliable systems of regenerative and dynamic braking are available to complement or replace traditional mechanical braking systems. The advantages of electric braking include control, reliability, mechanical simplicity, weight saving and, in certain cases, the opportunity to make use of the regenerated braking energy.

Cressall Resistors in profile
The world's foremost power resistor manufacturer, Cressall Resistors, offers an unrivalled combination of experience and expertise as well as the UK's widest range of resistor technologies. Cressall's customers include ABB, Siemens, Areva and Alstom, as well as major utilities such as Northern Powergrid and Western Power Distribution (WPD), EDF and Scottish Power. The company also works with countless smaller specialists such as CP Automation, HMK Automation and Drives and ACE Winches. Indeed, because of the fundamental nature of Cressall's product almost everyone in the electrical industry will have cause to contact the company at some point; making the Leicester based business a bellwether for the health of the sector itself.

For further information about the company's products, or to talk to Cressall about a bespoke project, view website: www.cressall.com

Quick page links - Display rates - Features - Magazine profile - Home page - Company index - Page 652


Industrial and Technological Publications
Leading the way in on-line magazine publishing
The Journal of Industry and Technology - Euro Technology - Industrial Analytical Instrumentation
Title registered in London 1978. Registration number 2334966

Twitter: www.twitter.com/@thejournalofind - Twitter: www.twitter.com/@eurotechnologym - Twitter: www,twitter.com/@industrialanaly
Google+: www.google.com/+ThejournalofindustryandtechnologyBiz21 Linkedin: www.linkedin.com/in/williamdigbyhammertonthejourna
Google+: www.Google.com/+Eurotechnologymagazine21E  Google+: www.google.com /+Industrialanalyticalinstrumentation21IA
Follow on Facebook: http://facebook.com/pages/The-Journal-of-Industry-and-Technology/171016159602089